What is CLI ?
Betaflight is also always being adjusted to support most current Cleanflight tools like Configurator and EzGui devices and many other MSP tools. There is no special tool needed just for betaflight. Tested Boards - Naze32 rev4, rev5 and rev6 (boards like dragonfly32, flip32 are all naze32 rev4 clones and just use naze target) - CC3D - SpracingF3. Betaflight is an excellent open source flight controller software, designed specially for mini quad (racing drones). Check out the FC Firmware Overview to learn more. I will walk you through Betaflight configurator, and show you the simple steps to setup your quadcopter in Betaflight for your first flight. JESC Firmware x 100. JESC: Betaflight RPM Filter on BLHeliS Hardware Quadcopter flight performance is greatly improve. $101.14 Ex Tax: $84.99. This involves holding down the boot button on your flight controller when pluggin it in to enter bootloader mode, and selecting the DFU mode within cleanflight or betaflight GUI. Blob.jpg 1025×550 174 KB.
CLI is abbreviation of the a Command Line Interface. It is special configuration mode where commands are given insted of the dedicated setting controls and inputs. Every flight controllers firmware configurator (Cleanflight, Betaflight, Butterflight, iNav, etc) has this mode. It is useful for more specific change of settings and detailed configuration the Flight Controller. It is also usefur for dumping the whole flight controller configuration, backuping and restoring the settings in the easy way. Read more about it below.
How to use CLI?
In order to start using CLI you have to connect to your flight controller with configurator software (See here how to install the standalone configurator software). Click on the “CLI” tab – this will enable flight controllers CLI mode. Write the command in the input field and hit the [Enter] to execute it.
You need to execute save command if you want all the commands and changes to be saved into Flight Controllers memory. Saving will reboot the flight controller. Close the CLI tab or send the exit command to exit the CLI mode without saving.
CLI Dump or Diff?
dump command dumps all the setting of the flight controller. This can be quite a long listdiff command was introduced in the BetaFlight version 3.0 and it dumps only the settings that are different from the defaults. diff all command dumps only differencies from the defaults but also dumps all the PID profiles.
It is highly recommended to use diff instead of the dump as it results in the significant smaller settings list and only the ones that were changed or differ from the defaults. Conan exiles offline mode mod.
How to Backup/Restore the settings using CLI?
Sometimes it is usefull to save the Flight Controller settings and restore them in case you need. These cases include FC firmware upgrade, restoring the FC to the point where it worked and etc. Backuping and restoring is very simple task.
Backup: Go to CLI, enter diff (or diff all if you have multiple PID profiles) and copy the provided text to anywhere just to save it for later use.
Restore: Go to CLI, paste the saved settings text to the command input field, hit [Enter]. Your FC settings are restored. Don’t forget to save the settings.
CLI commands list
| Command | Description |
|---|---|
1wire <esc> | passthrough 1wire to the specified esc |
adjrange | show/set adjustment ranges settings |
aux | show/set aux settings |
color | configure colors |
defaults | reset controller to defaults and reboot |
dump | print configurable settings in a pastable form |
diff | dump only the settings that are different from the defaults. Includes only the current PID profile. |
diff all | dump only the settings that are different from the defaults. Includes ALL PID profiles. |
exit | exit without saving |
feature | list or -val or val |
get | get the value of the specified variable |
gpspassthrough | passthrough gps to serial |
help | lists all commands |
led | configure leds |
map | mapping of rc channel order |
mixer | mixer name or list |
mode_color | configure mode colors |
motor | get/set motor output value |
play_sound | index, or none for next |
profile | index (0 to 2) |
rateprofile | index (0 to 2) |
rxrange | configure rx channel ranges (end-points) |
rxfail | show/set rx failsafe settings |
save | save settings and reboot |
serialpassthrough | serial passthrough mode, reset board to exit |
set | set the the given value to the variable. (name=value or blank or * for list) |
status | show system status |
version | show version |
serial | configure serial ports |
servo | configure servos |
sd_info | sdcard info |
tasks | show task stats |
mmix | design custom motor mixer |
smix | design custom servo mixer |
Betaflight Cong
Note that specific command list depends on the type of the firmware (BetaFlight, Butterflight, iNav) and firmware version you are using. For exact list of the commands type help in CLI mode.
Usefull CLI commands
Betaflight Configurator
bl or dfu command to enter the DFU mode without pushing the button. Reboots the FC board in bootloader mode.
set small_angle = 180 – sets any angle your quadcopter will be able to arm. Usefull when you land unexpectedly severely angled and you are unable to re-arm.
Pre ban norinco ak 47 serial numbers. Heidelberg manual. set ledstrip_visual_beeper = ON – When set to on, and the LEDLOW mode is active (i.e. LED strip off), blink the LED strip in synch with beeping, as a visual indicator in cases where the craft is too far away for the beeper to be heard / multiple craft are flying. Values available: [ON,OFF (default)]
Binding with integrated Receivers (connected via SPI):
For Betaflight 4.x – command bind_rx_spi
For Betaflight 3.x: – command frsky_bind
Don’t forget to issue save command after the sucessfull bind.
History:
2018-05-23 – article created
2019-02-13 – Usefull CLI commands updated
2019-07-01 – Usefull CLI commands updated
Betaflight Github
- Guide: How to Arm, PreArm and start your quad What is Arm and why do we need it? All modern quadcopters (or any
- ExpressLRS – Open Source Long Range radio control system – Complete Guide ExpressLRS is the Open Source Long Range radio control system, developed by Alessandro Carcione (aka AlessandroAU)